ISO 14743-2020 pdf free

04-21-2021 comment

ISO 14743-2020 pdf free.Pneumatic fluid power—Push-inconnectors for thermoplastic tubes.
1.Scope:This document specifies the general requirements and test methods for the design and performance ofpush-in connectors for use with thermoplastic tubes with outside diameters (OD) from 3 mm to 16 mmincluding dimensions in inches.
This document is intended to establish uniform methods of testing complete push-in connectorassemblies as used in pneumatic fluid power applications. It is not applicable to air braking systems.
2.Normative references:The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document. For dated references,only the edition cited applies. Forundated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7-1, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions,tolerancesand designation
ISO 4759-1,Tolerances for fasteners —Part 1: Bolts, screws, studs and nuts — Product grades A,B and CISO 5598, Fluid power systems and components — Vocabulary
ISO 8573-1:2010, Compressed air — Part 1: Contaminants and purity classes
ISO 10619-1, Rubber and plastics hoses and tubing —Measurement of flexibility and stiffness — Part 1:Bending tests at ambient temperature
ISO 16030, Pneumatic fluid power — Connections — Ports and stud endsANSI/ASME B1.1, Unified Inch Screw Threads, (UN and UNR Thread Form)ANSI/ASME B1.20.1, Pipe Threads, General Purpose, Inch
ANSI/ASME B1.20.3, Dryseal Pipe Threads (Inch)
3.Terms and definitions:For the purposes of this document, the terms and definitions given in ISO 5598 apply.
The connector assembly shall meet the performance requirements given in Clause 9 with tubesspecified in Annex A and Annex B.
When tubing with a lower rated pressure is used, the maximum working pressure of the tube andconnector assembly shall be that of the tubing.
In road vehicles, it is necessary to exercise special care to ensure that these connectors are never usedin an air braking system.
4.Push-in connector dimensions shown in Figures 2 to Z shall conform to the dimensions given inTables 1 to 7.
Hexagon tolerances across flats shall be in accordance with IS0 4759-1,Grade C. The minimumhexagon across-corner turn diameter of 1,092 times the normal across flats dimension shall be used.For connectors with the thread M and G, thread and stud end shall be in accordance with ISO 16030.For connector with the thread R, thread and stud end shall be in accordance with ISO 7-1.ISO 14743 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS ISO ASTM 52904:2021 pdf free Free AS Standards

AS ISO ASTM 52904:2021 pdf free

AS ISO ASTM 52904:2021 pdf free.Additive manufacturing - Process characteristics and performance - Practice for metal powder bed fusion process to meet critical applications. 5 Feedstock and Powder Batches 5.1 The material supplier shall package the powder...
Get More
AS ISO/ASTM 52901:2021 pdf free Free AS Standards

AS ISO/ASTM 52901:2021 pdf free

AS ISO ASTM 52901:2021 pdf free.Additive manufacturing - General principles - Requirements for purchased AM parts. 4.3.3 Tolerances The tolerances shall be specified (e.g. general tolerances, see ISO 2768-1 and ISO 2768-2, and/or specific, ISO 1101), including...
Get More
AS ISO 16809:2020 pdf free Free AS Standards

AS ISO 16809:2020 pdf free

AS ISO 16809:2020 pdf free.Non-destructive testing — Ultrasonic thickness measurement. 5 General requirements 5.1 Instruments The following types of instruments shall be used to achieve thickness measurement: a) dedicated ultrasonic thickness measurement instruments with numerical display showing...
Get More


Anonymous netizen Fill in information