AS/NZS 2891.5:2015 pdf free

09-08-2021 comment

AS/NZS 2891.5:2015 pdf free.Methods of sampling and testing asphalt Method 5: Compaction of asphalt by Marshall method and determination of stability and flow- Marshall procedure.
6 SPECIMEN PR EPARATION i
6.1 Laboratory prepared mix
Laboratory prepared mix shall be prepared as follows:
(a) Preheat the specimen mould assembly in the oven.
(b) If required, prepare a sample of asphalt in the laboratory in accordance with
AS/NZS 2891.2.1.
(c) Remove the specimen mould assembly from the oven and place a paper disc in the bottom of the mould.
(d) Obtain a representative test portion of the asphalt of sufficient mass to obtain a compacted specimen height of approximately 63.5 mm hut within the allowable range of 57 mm to 70 mm. Place the test portion in the mould and spade the asphalt with a heated spatula 1 5 times around the perimeter and 10 times over the interior.
NOTE: The expected bulk density of the compacted asphalt may he used to calculate the mass necessary to give the desired specimen height.
(e) Place the mould in the oven for sufficient time for the test portion to reach the specified compaction temperature. If the test portion has not reached the specified temperature within 60 minutes discard the test portion.
6.2 Plant produced mix
Plant produced mix shall be prepared as follows:
(a) Unless otherwise specified, obtain a bulk sample of asphalt in accordance with
AS/NZS 2891.1.1.
(h) Preheat the specimen mould assembly in the oven.
(c) Obtain a representative test portion of the asphalt of sufficient mass to obtain a compacted specimen height of approximately 63.5 mm but within the allowable range of 57 mm to 70 mm by either
(i) sample division of freshly produced asphalt that is at a temperature to facilitate sample division; or
(ii) placing a sample container in an oven, at a temperature not exceeding 160°C to reheat the sample. The sample shall not be in the oven for more than 3 h in total. When the sample is at a temperature to facilitate sample division remove the sample container from the oven and transfer the sample to a mixing tray or howl and prepare test portions.
NOTE: The expected bulk density of the compacted asphalt may he used to calculate the mass necessary to give the desired specimen height.
(d) Place the test portion in the mould and spade the asphalt with a heated spatula 15 times around the perimeter and 10 limes over the interior.
(e) Place the mould in the oven for sufficient time for the test portion to reach the specified compaction temperature. If the test portion has not reached the specified temperature within 60 mm discard the test portion.
7 COMPACTION OF SPECIMENS
The compaction procedure shall he as follows:
(a) Remove the mould from the oven. Place a thermometer in the mould and verify that the temperature of the asphalt in the mould is within the tolerance for the compaction temperature specified in Tables 1, 2 or 3. Record the temperature.
(b) Place a circular paper disc on top of the asphalt and transfer the mould assembly to the compaction pedestal.
(c) At a rate of 60 to 70 blows per minute, compact the mix using the specified number of blows of the compaction hammer with the hammer axis held vertically. Invert the mould and apply the same number of blows to the other end of the specimen.AS/NZS 2891.5 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS/NZS 60079.5:2015 pdf free Free AS Standards

AS/NZS 60079.5:2015 pdf free

AS/NZS 60079.5:2015 pdf free.Explosive atmospheres Part 5: Equipment protection by powdered filling 'q'. 4.1.1.3 Containers intended to be opened for repair Electrical equipment, parts of electrical equipment, or Ex components that are designed to be repaired shall...
Get More
AS/NZS 60079.2:2015 pdf free Free AS Standards

AS/NZS 60079.2:2015 pdf free

AS/NZS 60079.2:2015 pdf free.AUSTRALIAN/NEW ZEAL AND STANDARD Explosive atmospheres. 5 Constructional requirements for pressurized enclosures 5.1 Enclosure The pressurized enclosure shall have a degree of protection in accordance with Table 2. For Level of Protection pxb with...
Get More
AS/NZS 5263.1.3:2016 pdf free Free AS Standards

AS/NZS 5263.1.3:2016 pdf free

AS/NZS 5263.1.3:2016 pdf free.Gas appliances Part 1.3: Gas space heating appliances. 2.1 SCOPE This Clause of AS 5263.0 applies. 2.2 GENERAL DESIGN REQUIREMENTS This Clause of AS 5263.0 applies, except as modified below. 2.2.13 IJesign olappliance base...
Get More

LEAVE A REPLY

Anonymous netizen Fill in information