BS ISO 3584:2020 pdf free

04-20-2021 comment

BS ISO 3584:2020 pdf free.Road vehicles — Clevis couplings — Interchangeability.
This document specifies the characteristics necessary for the mounting and interchangeability of cleviscouplings on the frame (cross member, drawbeam or mounting bracket) of towing vehicles for trailers.This document is applicable to clevis couplings intended for connection to trailers equipped with adrawbar eye on the drawbar of the trailer.
Characteristics not specified are left to the discretion of the component manufacturer.
The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document.For dated references, only the edition cited applies. Forundated references, the latest edition of the referenced document (including any amendments) applies.ISo 1102,Commercial road vehicles — 50 mm drawbar eye — Interchangeability.ISO 8718,Road vehicles —Drawbar couplings and eyes for hinged drawbars —Strength tests ISO 8755,Commercial road vehicle — 40 mm drawbar eye — Interchangeability
ISO 12357,Commercial road vehicles — Drawbar couplings and eyes for rigid drawbars
No terms and definitions are listed in this document.
Reference may be made to this document both for clevis coupling mounting dimensions on theframe and for the separate clevis coupling.
Frames in conformance with this document shall be identified by the following information, in theorder given:
a) reference to this document;
b) number of the category according to Table 1.
EXAMPLE Frames with mounting dimensions according to category 3:Crossmember (or drawbeam or mounting bracket)ISO 3584—Category 3
Dimensional requirements on frame for mounting clevis coupling:Dimensions on the frame required for mounting of the clevis coupling (see Figure 2), such as theminimum flat surface defined by dimensions F and G, shall be as given in Table 2.Tolerances on drillingpattern dimensions shall be as shown in Figure 1. The requirements of 6.2 to 6.4 are applicable to all clevis couplings.Additional requirements applicableto C 40,C 50 and classified clevis couplings of both dimensions are given in 6.5.
The clevis coupling shall satisfy the tests specified in ISO 8718 or ISO 12357 or both.6.3Dimensional requirements
The maximum outer dimensions of all components of the clevis coupling shall be within the envelopebox defined in Table 3 (see Figure 3).
ln order to permit safer operation of the clevis coupling, there shall be adequate free space aroundactuating devices. Dimensions needed to ensure operating clearance for actuating devices are alsoshown in Figure 3.BS ISO 3584 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS ISO ASTM 52904:2021 pdf free Free AS Standards

AS ISO ASTM 52904:2021 pdf free

AS ISO ASTM 52904:2021 pdf free.Additive manufacturing - Process characteristics and performance - Practice for metal powder bed fusion process to meet critical applications. 5 Feedstock and Powder Batches 5.1 The material supplier shall package the powder...
Get More
AS ISO/ASTM 52901:2021 pdf free Free AS Standards

AS ISO/ASTM 52901:2021 pdf free

AS ISO ASTM 52901:2021 pdf free.Additive manufacturing - General principles - Requirements for purchased AM parts. 4.3.3 Tolerances The tolerances shall be specified (e.g. general tolerances, see ISO 2768-1 and ISO 2768-2, and/or specific, ISO 1101), including...
Get More
AS ISO 16809:2020 pdf free Free AS Standards

AS ISO 16809:2020 pdf free

AS ISO 16809:2020 pdf free.Non-destructive testing — Ultrasonic thickness measurement. 5 General requirements 5.1 Instruments The following types of instruments shall be used to achieve thickness measurement: a) dedicated ultrasonic thickness measurement instruments with numerical display showing...
Get More


Anonymous netizen Fill in information