AS ISO 7129:2021 pdf free

09-02-2021 comment

AS ISO 7129:2021 pdf free.Earth-moving machinery – Cutting edges used on tractor-dozers, graders and scrapers – Principal shapes and basic dimensions.
AS ISO 7129 specifies
— the principal shapes and dimensions of the cross-section,
— the hole location for the mounting bolts,
— the shapes and dimensions of holes for the mounting bolts,
for cutting used on tractor-dozers, graders and scrapers, as defined in ISO 6165, taking interchangeability into consideration.
NOTE Some values in inches in this International Standard are not equivalent to the corresponding values in millimetres because widely used values have been adopted.
2 Normative reference
The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
ISO 6165:1997, Earth-moving machinery — Basic types — Vocabulary.
3 Cross-sections of cutting edges — Principal shapes and basic dimensions
The principal shapes and basic dimensions of the cutting edge cross-section shall be as shown in figures land 2 and given in tables 1 and 2.
4 Mounting bolts一Hole locations
4.1 The hole locations for the mounting bolts shall be as follows:
a) for tractor-dozers and scrapers:
for cutting edge of width, W, of 330 mm or less, see figure 3 a),
for cutting edge of width, W, of over 330 mm, see figure 3 b);
b) for graders, see table 3 and figure 4.
NOTE The shapes and dimensions of cutting edges with a 140 mm hole pitch are specified in annex A.
4.2 Each countersink shall be located within a 3,2 mm (0,125 in) diameter of the positional tolerance.
4.3 The camber of the cutting edge shall be within 2 mm/m (0,08 in/39,4 in).
5 Mounting bolt holes一Shapes and dimensions
5.1 The shapes and dimensions of mounting bolts holes shall be those shown in figure 5 and given in table 4.
5.2 The inscribed circles of the square holes shall be concentric with the countersink to within 0,8 mm (0,032 in).AS ISO 7129 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS/NZS 60079.5:2015 pdf free Free AS Standards

AS/NZS 60079.5:2015 pdf free

AS/NZS 60079.5:2015 pdf free.Explosive atmospheres Part 5: Equipment protection by powdered filling 'q'. 4.1.1.3 Containers intended to be opened for repair Electrical equipment, parts of electrical equipment, or Ex components that are designed to be repaired shall...
Get More
AS/NZS 60079.2:2015 pdf free Free AS Standards

AS/NZS 60079.2:2015 pdf free

AS/NZS 60079.2:2015 pdf free.AUSTRALIAN/NEW ZEAL AND STANDARD Explosive atmospheres. 5 Constructional requirements for pressurized enclosures 5.1 Enclosure The pressurized enclosure shall have a degree of protection in accordance with Table 2. For Level of Protection pxb with...
Get More
AS/NZS 5263.1.3:2016 pdf free Free AS Standards

AS/NZS 5263.1.3:2016 pdf free

AS/NZS 5263.1.3:2016 pdf free.Gas appliances Part 1.3: Gas space heating appliances. 2.1 SCOPE This Clause of AS 5263.0 applies. 2.2 GENERAL DESIGN REQUIREMENTS This Clause of AS 5263.0 applies, except as modified below. 2.2.13 IJesign olappliance base...
Get More

LEAVE A REPLY

Anonymous netizen Fill in information