ISO/IEC 11801-4-2017 pdf free

06-16-2021 comment

ISO/IEC 11801-4-2017 pdf free.Information technology – Generic cabling for customer premises Part 4: Single-tenant homes.
This part of ISO/IEC 11801 specifies generic cabling for single-tenant homes. A home can contain one or more buildings or can be within a building that contains more than one home. It covers balanced cabling, optical fibre cabling and coaxial cabling.
This document specifies a generic cabling for two groups of applications:
1) information and communications technologies (ICT),
2) broadcast and communications technologies (BCT).
This document specifies directly or via reference to ISOIIEC 11801-1
a) the structure and minimum configuration for generic cabling within homes,
b) the interfaces at the telecommunications outlet (TO) and broadcast outlet (BO).
c) the performance requirements for cabling links and channels,
d) the implementation requirements and options.
e) the performance requirements for cabling components,
f) the conformance requirements and verification procedures.
Safety and electromagnetic compatibility (EMC) requirements are outside the scope of this document, and are covered by other standards and by regulations. However, information given by this document can be of assistance.
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
lEG 60728 (all parts), Cable networks for television signals, sound signals and interactive services
IEC 61754-20 (all parts), Fibre optic interconnecting devices and passive components — Fibre optic connector interfaces — Part 20: Type LC connector family
ISO/lEG 11801-1:2017, Information technology — Generic cabling for customer premises — Part 1: General requirements
ISO/lEG 14763-2, Information technology — Implementation and operation of customer premises cabling — Part 2: Planning and installation
ISOIIEC 30129, Information technology — Telecommunications bonding networks for buildings and other structures
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/IEC 11801-1,ISO/IEC 14763-2 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
IEC Electropedia: available at ht://ww.electropedia.org/
ISO Online browsing platform: available at htp://www.iso.org/obp
4.For a cabling installation to conform to this document the following applies.
a) The configuration and structure shall conform to the requirements outlined in Clause 5.
b) Channels shall meet the requirements specified in Clause 6 when subjected to environment conditions, local to the channels (see NOTE 2 below), as defined by the applicable environmental Class(es) of Clause 6. This shall be achieved by one of the following:
1) a channel design and implementation ensuring that the prescribed channel performance of Clause 6 is met:
2) attachment of appropriate components to a permanent link design meeting the prescribed performance class of Clause 7. Channel performance shall be ensured where a channel is created by adding more than one cord to either end of a link meeting the requirements of Clause 7;
3) for E1 environments, using the reference implementations of Clause 8 and compatible cabling components conforming to the requirements of Clauses 9, 10 and 11 based upon a statistical approach of performance modelling.
NOTE I This approach is not applicable to Class BCT-B cabling.
C) The interfaces to the cabling at the TO and BO shall conform to the requirements of Clause 10 with respect to mating interfaces and performance when subjected to environment conditions, local to the connecting hardware (see NOTE 2 below), as defined by the applicable environmental Class(es) of Clause 6.
d) Connecting hardware at other places in the cabling structure shall meet the performance requirements specified in Clause 10 when subjected to environment conditions, local to the connecting hardware (see NOTE 2 below), as defined by the applicable environmental Class(es) of Clause 6.
e) The requirements of ISO/IEC 14763-2 and ISO/IEC 30129 shall be met.
This document does not specify which tests and sampling levels should be adopted. Test methods to assess conformance with the channel and link requirements of Clause 6 and Clause 7, respectively, are specified in ISO/IEC 11801-1. The test parameters to be measured, the sampling levels and the treatment of measured results to be applied for particular installation shall be defined in the installation specification and quality plan for that installation prepared in accordance with ISO/IEC 14763-2.
In the absence of the channel, the conformance of the link shall be used to verify conformance with this document.
Specifications marked ffs are preliminary specifications, and are not required for conformance to this document.ISO/IEC 11801-4 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS ISO ASTM 52904:2021 pdf free Free AS Standards

AS ISO ASTM 52904:2021 pdf free

AS ISO ASTM 52904:2021 pdf free.Additive manufacturing - Process characteristics and performance - Practice for metal powder bed fusion process to meet critical applications. 5 Feedstock and Powder Batches 5.1 The material supplier shall package the powder...
Get More
AS ISO/ASTM 52901:2021 pdf free Free AS Standards

AS ISO/ASTM 52901:2021 pdf free

AS ISO ASTM 52901:2021 pdf free.Additive manufacturing - General principles - Requirements for purchased AM parts. 4.3.3 Tolerances The tolerances shall be specified (e.g. general tolerances, see ISO 2768-1 and ISO 2768-2, and/or specific, ISO 1101), including...
Get More
AS ISO 16809:2020 pdf free Free AS Standards

AS ISO 16809:2020 pdf free

AS ISO 16809:2020 pdf free.Non-destructive testing — Ultrasonic thickness measurement. 5 General requirements 5.1 Instruments The following types of instruments shall be used to achieve thickness measurement: a) dedicated ultrasonic thickness measurement instruments with numerical display showing...
Get More

LEAVE A REPLY

Anonymous netizen Fill in information