IEC 62061-2012 pdf free Functional safety of safety-related electrical

07-19-2021 comment

IEC 62061-2012 pdf free.Safety of machinery – Functional safety of safety-related electrical, electronic and programmable electronic control systems.
IEC 62061 specifies requirements and makes recommendations for the design. integration and validation of safety-related electrical, electronic and programmable electronic control systems (SRECS) for machines (see Notes 1 and 2). It is applicable to control systems used, either singly or in combination, to carry out safety-related control functions on machines that are not portable by hand while working, including a group of machines working together in a co-ordinated manner.
NOTE 1 In this standard, the term eIectricaI control systems is used to stand for Electrical, Electronic and Programmable Electronic (E/EIPE) control systems and “SRECS is used to stand for safety-related electrical, electronic and programmable electronic control systems.
NOTE 2 In this standard, it is presumed that the design of complex programmable electronic subsystems or subsystem elements conforms to the relevant requirements of IEC 61508 and uses Route IN (see IEC 61508-2:2010, 7.4.42). It is considered that Route 2H (see lEG 61508-2:2010, 7.4,4,3) is not suitable for general machinery. Therefore, this standard does not deal with Route 2u. This standard provides a methodology for the use, rather than development, of such subsystems and subsystem elements as part of a SRECS.
This standard is an application standard and is not intended to limit or inhibit technological advancement. It does not cover all the requirements (e.g. guarding, non-electrical interlocking or non-electrical control) that are needed or required by other standards or regulations in order to safeguard persons from hazards. Each type of machine has unique requirements to be satisfied to provide adequate safety.
This standard:
— is concerned only with functional safety requirements intended to reduce the risk of injury or damage to the health of persons in the immediate vicinity of the machine and those directly inThis International Standard specifies requirements and makes recommendations for the design. integration and validation of safety-related electrical, electronic and programmable electronic control systems (SRECS) for machines (see Notes 1 and 2). It is applicable to control systems used, either singly or in combination, to carry out safety-related control functions on machines that are not portable by hand while working, including a group of machines working together in a co-ordinated manner.
NOTE 1 In this standard, the term eIectricaI control systems is used to stand for Electrical, Electronic and Programmable Electronic (E/EIPE) control systems and “SRECS is used to stand for safety-related electrical, electronic and programmable electronic control systems.
NOTE 2 In this standard, it is presumed that the design of complex programmable electronic subsystems or subsystem elements conforms to the relevant requirements of IEC 61508 and uses Route IN (see IEC 61508-2:2010, 7.4.42). It is considered that Route 2H (see lEG 61508-2:2010, 7.4,4,3) is not suitable for general machinery. Therefore, this standard does not deal with Route 2u. This standard provides a methodology for the use, rather than development, of such subsystems and subsystem elements as part of a SRECS.
This standard is an application standard and is not intended to limit or inhibit technological advancement. It does not cover all the requirements (e.g. guarding, non-electrical interlocking or non-electrical control) that are needed or required by other standards or regulations in order to safeguard persons from hazards. Each type of machine has unique requirements to be satisfied to provide adequate safety.
This standard:
— is concerned only with functional safety requirements intended to reduce the risk of injury or damage to the health of persons in the immediate vicinity of the machine and those directly involved in the use of the machine;
— is restricted to risks arising directly from the hazards of the machine itself or from a group of machines working together in a co-ordinated manner;
NOTE 3 Requirements to mitigate risks arising from other hazards are provided in relevant sector standards. For example, where a machine(s) is part of a process activity, the machine electrical control system functional safety requirements should, In addition, satisfy other requirements (e.g. lEG 61511) insofar as safety of the process is concerned.
— does not specify requirements for the performance of non-electrical (e.g. hydraulic, pneumatic) control elements for machines;
NOTE 4 Although the requirements of this standard are specific to electrical control systems, the framework and methodology specified can be applicable to safety-related parts of control systems employing other technologies
— does not cover electrical hazards arising from the electrical control equipment itself (e.g. electric shock — see IEC 60204—1).IEC 62061 pdf free download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!

LEAVE A REPLY

Anonymous netizen Fill in information