AS/NZS 1859.1:2017 pdf free

09-08-2021 comment

AS/NZS 1859.1:2017 pdf free.Reconstituted wood-based panels – Specifications Part 1: Particleboard.
4,3 Particleboard
Panel material manufactured under pressure and heat from particles of wood (wood flakes, strands, chips, shavings, sawdust, and similar) andior lignocellulosic material in particle form (flax shives, hemp hurds, bagasse fragments. rice hulls, wheat straw and similar) with the addition of an adhesive.
Wood-based partickboard may be manufactured from virgin, reclaimed or recycled fibre or combinations of each.
4.4 keccled and reclaimed ssood
Recycled materials are defined in AS 4707. Within the definition for ‘Recycled material’, Item (a) refers to reclaimed fibre and Item (b) refers to recycled fibre.
Particleboard is classified as follows:
(a) Standard particleboard (STD) is intended for use in dry conditions, for example, for interior fitments (including furniture) in dry areas.
(b) Moisture resistant particleboard (MR) is intended for use in humid, interior conditions, for example, for interior fitmenis (including furniture) in humid areas such as occur in tropical climates and in kitchens, laundries and bathrooms, where occasional wetting may occur.
I MR particleboard should not be used where persistent wetting is likely. If particleboard is Id in continuously wet conditions, degradation will occur through adhesive failure and/or fungal attack.
2 Exterior use should be strictly in accordance with the manufacturer’s recommendations, instructions and guidelines.
6.1 General
Particleboard shall comply with the general requirements listed in Tables I and 2 when dispatched from the producing factory.
Some supplementary properties and their appropriate test methods are given in Clause .
6.2 Dimensions
Thickness, length, width and squareness tolerances shall he within the maximum tolerances stated in Tables I and 2 at dispatch from the producing factory.
NOTE: For certain types or uses of particleboards (see specific standards for panel types and performance standards), or in the case of dispatch in cut sizes, or where panels arc further machined, special tolerances for thickness, length and width may be agreed between the user and the supplier.
6.3 Formaldchde emission
For formaldehyde emission, the requirements in Table I are the specification limits. The requirements are fulfilled if at least 95% of the mean values for individual panels are equal to or below the upper specification limit.AS/NZS 1859.1 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS/NZS 60079.5:2015 pdf free Free AS Standards

AS/NZS 60079.5:2015 pdf free

AS/NZS 60079.5:2015 pdf free.Explosive atmospheres Part 5: Equipment protection by powdered filling 'q'. Containers intended to be opened for repair Electrical equipment, parts of electrical equipment, or Ex components that are designed to be repaired shall...
Get More
AS/NZS 60079.2:2015 pdf free Free AS Standards

AS/NZS 60079.2:2015 pdf free

AS/NZS 60079.2:2015 pdf free.AUSTRALIAN/NEW ZEAL AND STANDARD Explosive atmospheres. 5 Constructional requirements for pressurized enclosures 5.1 Enclosure The pressurized enclosure shall have a degree of protection in accordance with Table 2. For Level of Protection pxb with...
Get More
AS/NZS 5263.1.3:2016 pdf free Free AS Standards

AS/NZS 5263.1.3:2016 pdf free

AS/NZS 5263.1.3:2016 pdf free.Gas appliances Part 1.3: Gas space heating appliances. 2.1 SCOPE This Clause of AS 5263.0 applies. 2.2 GENERAL DESIGN REQUIREMENTS This Clause of AS 5263.0 applies, except as modified below. 2.2.13 IJesign olappliance base...
Get More


Anonymous netizen Fill in information