AS ISO 22915.16:2015 Pedestrian-propelled trucks

09-08-2021 comment

AS ISO 22915.16:2015 pdf download.Industrial trucks – Verification of stability Part 16: Pedestrian-propelled trucks.
This part of Iso 22915 specifies tests for verifying the stability of pedestrian-propelled trucks. It is applicable to
— straddle, pallet and platform stacker trucks with capacities not exceeding 1 000kg, with manual or battery-powered lift;
— scissors lift pallet trucks with lift heights up to 1 000 mm and rated capacity up to 1 000kg, with manual or battery-powered lift;
— platform trucks.
It also applies to trucks operating under the same conditions when equipped with load-handling attachments.
It is not applicable to trucks with retractable devices such as a mast or fork.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 229 15-1, Industrial trucks — Verification of stability — Part 1: General
ISO 3691-5:2014, Industrial trucks — Safety requirements and verification — PartS: Pedestrian-propelled trucks
ISO 5053, Powered industrial trucks — Terminology
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5053 and ISO 22951-1 apply.
4 Requirements
4.1 General
See ISO 22915-1.
4.2 Position of the truck on the tilt table
All tests shall be carried out with castors and swivelling wheels, when fitted, in the position of least stability (see Tables 1, 2 and 3).
4.2.2 Tests 1,2,4 and 7 to 10 for longitudinal direction of test
The truck shall be positioned on the tilt table with the steer axle B-B and the load axle C—C parallel to
the tilt axis X—Y of the tilt table.
4.2.3 Tests 3,5, 6 and 7 to 10 for lateral direction of test
The truck shall be positioned on the tilt table with the line M—N parallel to the tilt axis X—Y of the tilt table.
Point M is defined as follows:
a) For trucks with one or more non-sprung castor wheels, point M is the vertical projection onto the tilt table of the point of intersection between the centreline of the castor wheel axle and the midpoint of the wheel(s), with the non-sprung castor being positioned with the centreline of the castor wheel axle parallel to tilt axis X—Y orat any other orientation that produces minimum stability.
b) For trucks having non- articulating dual steer wheels, point M is the vertical projection onto the tilt table of the point of intersection between the centreline of the steer axle and the centreline of the width over both steer wheels, with the axle of the steer wheels positioned parallel to the tilt axis X—Y or at any other orientation that produces minimum stability.
c) For trucks with stabilizers, point M is the vertical projection onto the tilt table of the point of symmetry of the stabilizer contact surface.
Point N is defined as the centre point of the area of contact between the tilt table surface and the load wheel nearest to the tilt axis X—Y of the tilt table.
5 Verification of stability
5.1 Dynamic test — Platform trucks
This dynamic test applies only to platform trucks.AS ISO 22915.16 pdf download.

Download infomation Go to download
Note: Can you help me share this website on your Facebook or others? Many thanks!
AS/NZS 60079.5:2015 pdf free Free AS Standards

AS/NZS 60079.5:2015 pdf free

AS/NZS 60079.5:2015 pdf free.Explosive atmospheres Part 5: Equipment protection by powdered filling 'q'. 4.1.1.3 Containers intended to be opened for repair Electrical equipment, parts of electrical equipment, or Ex components that are designed to be repaired shall...
Get More
AS/NZS 60079.2:2015 pdf free Free AS Standards

AS/NZS 60079.2:2015 pdf free

AS/NZS 60079.2:2015 pdf free.AUSTRALIAN/NEW ZEAL AND STANDARD Explosive atmospheres. 5 Constructional requirements for pressurized enclosures 5.1 Enclosure The pressurized enclosure shall have a degree of protection in accordance with Table 2. For Level of Protection pxb with...
Get More
AS/NZS 5263.1.3:2016 pdf free Free AS Standards

AS/NZS 5263.1.3:2016 pdf free

AS/NZS 5263.1.3:2016 pdf free.Gas appliances Part 1.3: Gas space heating appliances. 2.1 SCOPE This Clause of AS 5263.0 applies. 2.2 GENERAL DESIGN REQUIREMENTS This Clause of AS 5263.0 applies, except as modified below. 2.2.13 IJesign olappliance base...
Get More

LEAVE A REPLY

Anonymous netizen Fill in information